- Maxi pc suite free download install#
- Maxi pc suite free download drivers#
- Maxi pc suite free download update#
- Maxi pc suite free download driver#
- Maxi pc suite free download manual#
If you have performed all the steps above and are still having problems, check the following.
Maxi pc suite free download drivers#
Remember to always allow firewall preferences or new Autel drivers to be installed.
Maxi pc suite free download update#
You may be prompted to perform an update such as in the demonstration video aboveif so its a good idea to keep the software up to date.
Maxi pc suite free download driver#
The Printer Driver will open and you will see a printer icon in the bottom right of your PC, next to the Time and Date. Within this folder you will find MaxiSys Printer. Once installation has finished, you will need to open the MaxiSys Printer. You must accept these preferences or the software will be blocked and printing will not work. This is because the software is communicating with your network.
Maxi pc suite free download install#
During installation you may be prompted to Install Drivers or if you have a firewall, to allow the software certain security preferences.
The welcome screen of the PC suite should now bootup. Autel J2534 driver for ECU programming Install Guidance Inside this folder you should see an icon calledAutorun. The software may load automatically, but if not, Click Start and then My Computer.ĭouble click to open this up. Therefor, the following all need to be connected to the SAME network and turned on. The MaxiSys via being connected to the same network as your PC sends the data to the PC, which in turn prints the data. Then, when you send a Print command from your MaxiSys, the MaxiSys will search the network for PCs that have the print driver installed. So how does this diagram work? You then connect your MaxiSys to the same network. Firstly, have a look at the diagram below. A Windows Based PC with full administrative Rights be able to run programs in administrative mode To make sure the PC is connected to the network either wirelessly via Ethernet. A Wireless Network - such as a broadband router. An active Internet connection on your PC. This sounds a lot more complicated than it really is. Bob DiVincenzo Reply to:Bluehog.Wireless printing can be difficult to get your head around as it requires your MaxiSys to communicate with your PC through a network. Maybe 64GB was too high for it to read? Hope this helps. Since the updates only came to about 2 or 3GB, I went ahead and put the updates on the card that came with the scanner and now when I plug it into my car, it works. So I did my update on a card that was 64GB. I hope this help, the fact is that the PC Windows 10 have problems recognizing the Microcard inside the Maxilink as a Drive, and there lies the problem, but if you take it outupdate it with an adapter, put it back in the MaxiLink, run your test, and then connect to the PC, run the Playback button, run PC Link, everything works fine. I put it back in the MaxiLink and connected the unit to my Audi, and I run every test I could with the unit. If you remove the card and put it into an Adapter for regular SD card and provided you have a port for it, is recognized immediately as a Drive and the Maxi PC Suite recognize it and you can download your updates.
Maxi pc suite free download manual#
So their response was to read you the manual and not deal with has become a known issue connecting the ML to a PC? Here was their response: Hello Sir, Thank you for email. Maxilink ML unable to connect to my computer.īluehog I have tried 3 different USB ports directly on the desktop computer not thru a hub or display. For more detailed steps, please refer to of user manual above. The your device can be recognized the app, and you will be ready for printing. If you were trying to print via Autel Printer, you should connect the device to computer with USB cable, run Autel Printer software on computer, select Playback on the main screen of the device. Or you can take out the TF card from the scan tool and load it to computer with a card reader. Please make sure you fully understand all instructions on updating and printing for ML Left Scroll button and connect the device to computer with USB cable. Seems I missed some instructions that I originally followed My Bad! This did not repair the problem Hope someone from Autel can help Thought I would give an update I contacted Autel support. I then reinstalled the Suite which also reinstalled the PC Link print program. I originally downloaded the software and did a full vehicle update This removed the suite software as well as the PC Link print software.
0 kommentar(er)
